|
3 Replies and 5516 Views
Materials and DWG files
5516 3 - Started by Sivert Lundstrøm, last post from Lars Wernlund
Hello
Is there a way to sett different materials or textures on imported DWG files. If you use the premade forms or objects in Capture you can sett materials, but not on imported forms
Working with Sketchup and exports as DWG to Capture.
And how do I make the groups in Sketchup work in Capture
|
|
|
1 Replies and 3842 Views
CONE
3842 1 - Started by Wlodek Duval, last post from Lars Wernlund
Is it possible to draw cone with:
top diameter 120m
bottom diameter 80m
high 15m
and add materials for it
|
|
|
2 Replies and 5117 Views
No DMX values in Capture
5117 2 - Started by ryan, last post from ryan
I am using Capture as my visualizer for Light Factory (LF). Before upgrading to the latest versions of both LF and Capture I was able to control lights in Capture from LF without issue. However, after the upgrade, the DMX values are not showing up in Capture. I know the two applications are still communicating because I can select lights in LF and the corresponding light in Capture is selected (or highlighted).
Any ideas what could be causing this
-Ryan
|
|
|
5 Replies and 9962 Views
Realistic hardware spec
9962 5 - Started by Deleted User, last post from Deleted User
Hi All, I’m looking into hiring - or possibly even trying to buy, a PC or Mac system that will run Capture visualisation smoothly for pre programming an upcoming show. It'll need to run approx 150 generic fixture, 20- 30 moving fixtures, plus LED battens within a venue drawing and associated surfaces effecting light. Can any of you offer advice on realistic processor, graphics card and memory spec for either PC or Mac that you have experience of being stable
Many thanks for your time.
.
|
|
|
1 Replies and 4385 Views
working with dwg files
4385 1 - Started by matt, last post from Lars Wernlund
hello
whenever i try importing a dwg file it crashes capture. i am trying to import dwg from vector works
is the any instructions one should follow to successfully import dwg and perhaps a list of what 3rd party drawing software which works along side capture
cheers
matt
|
|
|
1 Replies and 4255 Views
control fixture
4255 1 - Started by Deleted User, last post from Lars Wernlund
Hello could you help meI would like to create 2 channel for a ramp of 10 to dimmer dmx, in two colors on projectors showtec / arrays / sunstrip.I do not arrive has to separate them, and to control them.thanks
|
|
|
2 Replies and 4977 Views
import jpeg
4977 2 - Started by Deleted User, last post from Deleted User
Hello... I would want know the procedure to import a JPEG file.The same manipulation as for an import of file dwg is it.This JPEG file is intended to serve as texture for walls and groundsthanks a lot
|
|
|
2 Replies and 4854 Views
how to import dxf o dwg
4854 2 - Started by Deleted User, last post from Lars Wernlund
Hello, I possede the complete version of capture polar 2.37, and I work on mac osx10.6 I do not arrive import my plant dxf.Which is the procedure to import these plans. Open. Extract. thanks
|
|
|
3 Replies and 6294 Views
Automatic on truss
6294 3 - Started by Pat, last post from Lars Wernlund
Hello Lars,
If you have a fixture and move this it is red.
Now I have a problem because if you move it to close to the truss it turns to magenta sticks and on the truss or changes position etc etc. Can you set this function off and where
Regards,
Pat
|
|
|
|